[rešeno] [13.04] težave z wifi rtl8723ae
nezolina
Član
pozdravljeni.
sem novopečena uporabnica ubuntuja 13.04 na laptopu toshiba c855 z mrežno realtek rtl8723ae, ki mi povzroča preglavice. včasih dela, včasih pa ne
ko dela, se lepo samodejno poveže, ko pa ne dela pa zahteva od mene geslo, ampak se ne poveže.potem vsake par minut zahteva geslo.tudi ko sem povezana z drugo kartico (usb-belkin), mi "teži".ko je v mirovanju (zaslon dol), se zgodi,da se odpre toliko oken, da jih potem komaj vse zaprem.rada bi uporabljala notranjo kartico, saj je usb prevelik in preveč "štrli" iz laptopa, ki pa je seveda namenjen mobilni uporabi. :rolleyes:
kaj bi lahko bilo narobe v mojem primeru in kako lahko to popravim?
lepo prosim za pomoč!
hvala!
sem novopečena uporabnica ubuntuja 13.04 na laptopu toshiba c855 z mrežno realtek rtl8723ae, ki mi povzroča preglavice. včasih dela, včasih pa ne
ko dela, se lepo samodejno poveže, ko pa ne dela pa zahteva od mene geslo, ampak se ne poveže.potem vsake par minut zahteva geslo.tudi ko sem povezana z drugo kartico (usb-belkin), mi "teži".ko je v mirovanju (zaslon dol), se zgodi,da se odpre toliko oken, da jih potem komaj vse zaprem.rada bi uporabljala notranjo kartico, saj je usb prevelik in preveč "štrli" iz laptopa, ki pa je seveda namenjen mobilni uporabi. :rolleyes:
kaj bi lahko bilo narobe v mojem primeru in kako lahko to popravim?
lepo prosim za pomoč!
hvala!
Komentarji
ter prilepiš kaj ti izpiše
neza@neza-SATELLITE-C855-1T2:~$ lshw -c network
WARNING: you should run this program as super-user.
*-network
description: Wireless interface
product: RTL8723AE PCIe Wireless Network Adapter
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlan1
version: 00
serial: 20:68:9d:8b:24:42
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=rtl8723ae driverversion=3.8.0-19-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn
resources: irq:17 ioport:3000(size=256) memory:c2400000-c2403fff
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:03:00.0
logical name: eth0
version: 05
serial: 4c:72:b9:d7:2d:f6
size: 10Mbit/s
capacity: 100Mbit/s
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s
resources: irq:41 ioport:2000(size=256) memory:c0004000-c0004fff memory:c0000000-c0003fff
*-network
description: Wireless interface
physical id: 1
bus info: usb@1:1.2
logical name: wlan0
serial: 00:22:75:3b:67:17
capabilities: ethernet physical wireless
configuration: broadcast=yes driver=rt2800usb driverversion=3.8.0-19-generic firmware=0.29 ip=192.168.0.102 link=yes multicast=yes wireless=IEEE 802.11bgn
WARNING: output may be incomplete or inaccurate, you should run this program as super-user.
neza@neza-SATELLITE-C855-1T2:~$
Ker opažam da je pravi driver gor..
Brez skrbi.. super-user si samo takrat ko to dejansko rabiš (vpišeš svoje geslo za posodobitev paketov ter z uporabo 'sudo krnekukaz' v terminalu) in ne vedno
dmesg se mi pa to izpiše:
n, max_eirp)
[19974.110777] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[19974.110779] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[19974.110781] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[19974.110783] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[19974.110785] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[20395.912416] wlan1: authenticate with a0:f3:c1:81:eb:f4
[20395.944137] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[20395.945546] wlan1: authenticated
[20395.947631] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[20395.951408] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[20395.951585] wlan1: associated
[20405.952570] wlan1: disassociating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[20405.993506] wlan1: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[20405.994276] cfg80211: Calling CRDA to update world regulatory domain
[20406.002326] cfg80211: World regulatory domain updated:
[20406.002334] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[20406.002340] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[20406.002346] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[20406.002350] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[20406.002354] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[20406.002358] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[20827.779023] wlan1: authenticate with a0:f3:c1:81:eb:f4
[20827.810759] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[20827.813728] wlan1: authenticated
[20827.814288] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[20827.824378] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[20827.824548] wlan1: associated
[20830.828249] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 2)
[20830.845119] cfg80211: Calling CRDA to update world regulatory domain
[20830.851560] cfg80211: World regulatory domain updated:
[20830.851564] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[20830.851567] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[20830.851569] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[20830.851571] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[20830.851573] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[20830.851575] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21252.644192] wlan1: authenticate with a0:f3:c1:81:eb:f4
[21252.681159] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[21252.685537] wlan1: authenticated
[21252.687121] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[21252.690829] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[21252.690984] wlan1: associated
[21261.543534] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 6)
[21261.561170] cfg80211: Calling CRDA to update world regulatory domain
[21261.568926] cfg80211: World regulatory domain updated:
[21261.568935] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[21261.568941] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21261.568946] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[21261.568950] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[21261.568954] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21261.568958] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21528.728241] wlan1: authenticate with a0:f3:c1:81:eb:f4
[21528.760110] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[21528.762047] wlan1: authenticated
[21528.763403] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[21528.768858] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[21528.769040] wlan1: associated
[21538.769527] wlan1: disassociating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[21538.812631] cfg80211: Calling CRDA to update world regulatory domain
[21538.812772] wlan1: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[21538.817772] cfg80211: World regulatory domain updated:
[21538.817776] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[21538.817779] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21538.817781] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[21538.817783] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[21538.817785] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21538.817787] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[21552.635961] usb 1-1.2: new high-speed USB device number 8 using ehci-pci
[21552.748879] usb 1-1.2: New USB device found, idVendor=050d, idProduct=815c
[21552.748889] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[21552.748896] usb 1-1.2: Product: F5D8053 N Wireless USB Adapter
[21552.748901] usb 1-1.2: Manufacturer: Belkin
[21552.827894] usb 1-1.2: reset high-speed USB device number 8 using ehci-pci
[21552.957320] ieee80211 phy2: Selected rate control algorithm 'minstrel_ht'
[21553.198981] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[21553.199937] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[21578.697858] wlan0: authenticate with a0:f3:c1:81:eb:f4
[21578.735023] wlan0: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[21578.736448] wlan0: authenticated
[21578.739441] wlan0: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[21578.747475] wlan0: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[21578.757298] wlan0: associated
[21578.757315] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[21844.395038] wlan1: authenticate with a0:f3:c1:81:eb:f4
[21844.420623] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[21844.422055] wlan1: authenticated
[21844.423554] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[21844.427310] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=2)
[21844.427525] wlan1: associated
[21847.431405] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 2)
[22153.294043] wlan1: authenticate with a0:f3:c1:81:eb:f4
[22153.325739] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[22153.330354] wlan1: authenticated
[22153.333274] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[22153.338671] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=2)
[22153.338842] wlan1: associated
[22163.338819] wlan1: disassociating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[22163.382919] wlan1: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[22268.046666] wlan0: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[22268.096070] cfg80211: Calling CRDA to update world regulatory domain
[22268.107016] cfg80211: World regulatory domain updated:
[22268.107020] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[22268.107023] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[22268.107025] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[22268.107027] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[22268.107029] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[22268.107031] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[22269.189291] PM: Syncing filesystems ... done.
[22269.428637] Freezing user space processes ... (elapsed 0.01 seconds) done.
[22269.444428] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[22269.460884] Suspending console(s) (use no_console_suspend to debug)
[22269.461241] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[22269.461322] sd 0:0:0:0: [sda] Stopping disk
[22270.132227] PM: suspend of devices complete after 671.425 msecs
[22270.132371] PM: late suspend of devices complete after 0.142 msecs
[22270.132565] r8169 0000:03:00.0: System wakeup enabled by ACPI
[22270.164440] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[22270.180500] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[22270.212296] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[22270.228117] PM: noirq suspend of devices complete after 95.770 msecs
[22270.228569] ACPI: Preparing to enter system sleep state S3
[22270.228819] PM: Saving platform NVS memory
[22270.326890] Disabling non-boot CPUs ...
[22270.327085] Broke affinity for irq 16
[22270.327094] Broke affinity for irq 17
[22270.327104] Broke affinity for irq 23
[22270.327107] Broke affinity for irq 42
[22270.328131] smpboot: CPU 1 is now offline
[22270.329438] ACPI: Low-level resume complete
[22270.329490] PM: Restoring platform NVS memory
[22270.332193] Enabling non-boot CPUs ...
[22270.332264] smpboot: Booting Node 0 Processor 1 APIC 0x2
[22270.345735] CPU1 is up
[22270.350107] ACPI: Waking up from system sleep state S3
[22270.547970] toshiba_bluetooth: Re-enabling Toshiba Bluetooth
[22270.580299] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[22270.611834] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[22270.643785] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[22270.691695] PM: noirq resume of devices complete after 143.526 msecs
[22270.691834] PM: early resume of devices complete after 0.110 msecs
[22270.691860] i915 0000:00:02.0: setting latency timer to 64
[22270.692222] xhci_hcd 0000:00:14.0: setting latency timer to 64
[22270.692316] mei 0000:00:16.0: irq 43 for MSI/MSI-X
[22270.692350] ehci-pci 0000:00:1a.0: setting latency timer to 64
[22270.692401] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[22270.692464] ehci-pci 0000:00:1d.0: setting latency timer to 64
[22270.692491] ahci 0000:00:1f.2: setting latency timer to 64
[22270.692561] rtlwifi: wireless switch is on
[22270.692570] r8169 0000:03:00.0: System wakeup disabled by ACPI
[22270.707673] toshiba_bluetooth: Re-enabling Toshiba Bluetooth
[22270.915577] usb 2-1.3: reset full-speed USB device number 3 using ehci-pci
[22271.008326] btusb 2-1.3:1.0: no reset_resume for driver btusb?
[22271.008330] btusb 2-1.3:1.1: no reset_resume for driver btusb?
[22271.027396] ata5: SATA link down (SStatus 0 SControl 300)
[22271.043529] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[22271.053436] ata3.00: configured for UDMA/100
[22271.751378] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[22272.770977] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[22272.772599] ata1.00: configured for UDMA/100
[22272.786992] sd 0:0:0:0: [sda] Starting disk
[22272.816381] PM: resume of devices complete after 2125.219 msecs
[22272.816751] Restarting tasks ... done.
[22272.831649] video LNXVIDEO:00: Restoring backlight state
[22272.894943] usb 1-1.1: new high-speed USB device number 9 using ehci-pci
[22273.244964] usb 1-1.1: New USB device found, idVendor=0bda, idProduct=0138
[22273.244970] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[22273.244973] usb 1-1.1: Product: USB2.0-CRW
[22273.244975] usb 1-1.1: Manufacturer: Generic
[22273.244977] usb 1-1.1: SerialNumber: 20090516388200000
[22273.284322] scsi8 : usb-storage 1-1.1:1.0
[22273.482453] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[22273.509314] usb 1-1.1: USB disconnect, device number 9
[22273.677541] r8169 0000:03:00.0 eth0: link down
[22273.677608] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[22273.881634] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[22276.194997] wlan1: authenticate with a0:f3:c1:81:eb:f4
[22276.226208] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[22276.227620] wlan1: authenticated
[22276.229810] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[22276.233471] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[22276.233692] wlan1: associated
[22276.233703] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[22276.852302] wlan0: authenticate with a0:f3:c1:81:eb:f4
[22276.891815] wlan0: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[22276.893287] wlan0: authenticated
[22276.893621] wlan0: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[22276.897537] wlan0: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=2)
[22276.910018] wlan0: associated
[22276.910067] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[22284.297587] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 6)
[22590.026428] wlan1: authenticate with a0:f3:c1:81:eb:f4
[22590.058122] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[22590.059860] wlan1: authenticated
[22590.061779] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[22590.065656] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[22590.065819] wlan1: associated
[22613.110824] usb 1-1.2: USB disconnect, device number 8
[22613.113672] phy2 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x7010 with error -19.
[22613.123622] phy2 -> rt2x00usb_regbusy_read: Error - Indirect register access failed: offset=0x00007010, value=0xffff8801
[22613.154976] wlan0: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[23299.051498] wlan1: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[23299.090439] cfg80211: Calling CRDA to update world regulatory domain
[23299.100136] cfg80211: World regulatory domain updated:
[23299.100144] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[23299.100150] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23299.100155] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23299.100160] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23299.100164] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23299.100169] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23301.264914] PM: Syncing filesystems ... done.
[23301.492824] Freezing user space processes ... (elapsed 0.01 seconds) done.
[23301.507762] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[23301.524199] Suspending console(s) (use no_console_suspend to debug)
[23301.524550] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[23301.541186] sd 0:0:0:0: [sda] Stopping disk
[23302.187555] PM: suspend of devices complete after 663.426 msecs
[23302.187697] PM: late suspend of devices complete after 0.140 msecs
[23302.187890] r8169 0000:03:00.0: System wakeup enabled by ACPI
[23302.219762] ehci-pci 0000:00:1d.0: System wakeup enabled by ACPI
[23302.239391] ehci-pci 0000:00:1a.0: System wakeup enabled by ACPI
[23302.271619] xhci_hcd 0000:00:14.0: System wakeup enabled by ACPI
[23302.287441] PM: noirq suspend of devices complete after 99.771 msecs
[23302.287894] ACPI: Preparing to enter system sleep state S3
[23302.288153] PM: Saving platform NVS memory
[23302.386195] Disabling non-boot CPUs ...
[23302.386436] Broke affinity for irq 16
[23302.386445] Broke affinity for irq 17
[23302.386455] Broke affinity for irq 23
[23302.386458] Broke affinity for irq 42
[23302.387481] smpboot: CPU 1 is now offline
[23302.388842] ACPI: Low-level resume complete
[23302.388894] PM: Restoring platform NVS memory
[23302.391610] Enabling non-boot CPUs ...
[23302.391681] smpboot: Booting Node 0 Processor 1 APIC 0x2
[23302.405147] CPU1 is up
[23302.409473] ACPI: Waking up from system sleep state S3
[23302.607304] toshiba_bluetooth: Re-enabling Toshiba Bluetooth
[23302.639632] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[23302.671163] ehci-pci 0000:00:1a.0: System wakeup disabled by ACPI
[23302.703121] ehci-pci 0000:00:1d.0: System wakeup disabled by ACPI
[23302.751031] PM: noirq resume of devices complete after 143.530 msecs
[23302.751166] PM: early resume of devices complete after 0.107 msecs
[23302.751192] i915 0000:00:02.0: setting latency timer to 64
[23302.751237] xhci_hcd 0000:00:14.0: setting latency timer to 64
[23302.751329] mei 0000:00:16.0: irq 43 for MSI/MSI-X
[23302.751741] ehci-pci 0000:00:1a.0: setting latency timer to 64
[23302.751795] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[23302.751859] ehci-pci 0000:00:1d.0: setting latency timer to 64
[23302.751888] ahci 0000:00:1f.2: setting latency timer to 64
[23302.751913] rtlwifi: wireless switch is on
[23302.751922] r8169 0000:03:00.0: System wakeup disabled by ACPI
[23302.767089] toshiba_bluetooth: Re-enabling Toshiba Bluetooth
[23302.974844] usb 2-1.3: reset full-speed USB device number 3 using ehci-pci
[23303.067795] btusb 2-1.3:1.0: no reset_resume for driver btusb?
[23303.067799] btusb 2-1.3:1.1: no reset_resume for driver btusb?
[23303.094735] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[23303.102738] ata5: SATA link down (SStatus 0 SControl 300)
[23303.104649] ata3.00: configured for UDMA/100
[23303.918687] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[23304.822187] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[23304.823821] ata1.00: configured for UDMA/100
[23304.838333] sd 0:0:0:0: [sda] Starting disk
[23304.868756] PM: resume of devices complete after 2118.260 msecs
[23304.869127] Restarting tasks ... done.
[23304.880364] video LNXVIDEO:00: Restoring backlight state
[23304.948685] usb 1-1.1: new high-speed USB device number 10 using ehci-pci
[23305.295800] usb 1-1.1: New USB device found, idVendor=0bda, idProduct=0138
[23305.295810] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[23305.295816] usb 1-1.1: Product: USB2.0-CRW
[23305.295821] usb 1-1.1: Manufacturer: Generic
[23305.295834] usb 1-1.1: SerialNumber: 20090516388200000
[23305.339351] scsi9 : usb-storage 1-1.1:1.0
[23305.441267] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[23305.568609] usb 1-1.1: USB disconnect, device number 10
[23305.636926] r8169 0000:03:00.0 eth0: link down
[23305.636992] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[23307.938573] wlan1: authenticate with a0:f3:c1:81:eb:f4
[23307.969662] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23307.971132] wlan1: authenticated
[23307.973219] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23307.976962] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[23307.977130] wlan1: associated
[23307.977167] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[23317.977539] wlan1: disassociating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[23318.014688] cfg80211: Calling CRDA to update world regulatory domain
[23318.015121] wlan1: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[23318.020737] cfg80211: World regulatory domain updated:
[23318.020741] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[23318.020744] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23318.020746] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23318.020748] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23318.020750] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23318.020752] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23340.647904] wlan1: authenticate with a0:f3:c1:81:eb:f4
[23340.681154] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23340.684561] wlan1: authenticated
[23340.690779] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23340.697038] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[23340.697217] wlan1: associated
[23343.699840] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 2)
[23343.727092] cfg80211: Calling CRDA to update world regulatory domain
[23343.733691] cfg80211: World regulatory domain updated:
[23343.733695] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[23343.733697] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23343.733700] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23343.733701] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23343.733703] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23343.733705] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23350.540613] wlan1: authenticate with a0:f3:c1:81:eb:f4
[23350.572211] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23350.577082] wlan1: authenticated
[23350.579649] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23350.587216] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[23350.587388] wlan1: associated
[23353.592040] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 2)
[23353.608911] cfg80211: Calling CRDA to update world regulatory domain
[23353.620082] cfg80211: World regulatory domain updated:
[23353.620091] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[23353.620096] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23353.620101] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23353.620106] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[23353.620110] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23353.620114] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[23369.005885] usb 1-1.2: new high-speed USB device number 11 using ehci-pci
[23369.118959] usb 1-1.2: New USB device found, idVendor=050d, idProduct=815c
[23369.118970] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[23369.118977] usb 1-1.2: Product: F5D8053 N Wireless USB Adapter
[23369.118982] usb 1-1.2: Manufacturer: Belkin
[23369.197830] usb 1-1.2: reset high-speed USB device number 11 using ehci-pci
[23369.327562] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht'
[23369.556947] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[23369.557829] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[23372.067264] wlan0: authenticate with a0:f3:c1:81:eb:f4
[23372.100200] wlan0: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23372.101638] wlan0: authenticated
[23372.104827] wlan0: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23372.108543] wlan0: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[23372.118485] wlan0: associated
[23372.118585] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[23660.322173] wlan1: authenticate with a0:f3:c1:81:eb:f4
[23660.353685] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23660.355256] wlan1: authenticated
[23660.357431] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23660.361349] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=2)
[23660.361511] wlan1: associated
[23663.364185] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 2)
[23968.227398] wlan1: authenticate with a0:f3:c1:81:eb:f4
[23968.251752] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23968.253845] wlan1: authenticated
[23968.255211] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23968.259675] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=2)
[23968.259844] wlan1: associated
[23972.282041] wlan1: deauthenticated from a0:f3:c1:81:eb:f4 (Reason: 2)
[23973.702655] wlan1: authenticate with a0:f3:c1:81:eb:f4
[23973.734066] wlan1: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[23973.736338] wlan1: authenticated
[23973.737438] wlan1: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[23973.741155] wlan1: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=2)
[23973.741306] wlan1: associated
[24472.825503] usb 1-1.2: USB disconnect, device number 11
[24472.855316] wlan0: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[24521.244619] wlan1: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[24521.288492] cfg80211: Calling CRDA to update world regulatory domain
[24521.292195] cfg80211: World regulatory domain updated:
[24521.292198] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[24521.292201] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[24521.292203] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[24521.292205] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[24521.292207] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[24521.292209] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[24692.129421] usb 1-1.2: new high-speed USB device number 12 using ehci-pci
[24692.242225] usb 1-1.2: New USB device found, idVendor=050d, idProduct=815c
[24692.242230] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[24692.242233] usb 1-1.2: Product: F5D8053 N Wireless USB Adapter
[24692.242235] usb 1-1.2: Manufacturer: Belkin
[24692.321355] usb 1-1.2: reset high-speed USB device number 12 using ehci-pci
[24692.450699] ieee80211 phy4: Selected rate control algorithm 'minstrel_ht'
[24692.676461] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[24692.677410] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[24695.183079] wlan0: authenticate with a0:f3:c1:81:eb:f4
[24695.223673] wlan0: send auth to a0:f3:c1:81:eb:f4 (try 1/3)
[24695.225123] wlan0: authenticated
[24695.228235] wlan0: associate with a0:f3:c1:81:eb:f4 (try 1/3)
[24695.231754] wlan0: RX AssocResp from a0:f3:c1:81:eb:f4 (capab=0x431 status=0 aid=1)
[24695.241606] wlan0: associated
[24695.242022] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[25007.495795] usb 1-1.2: USB disconnect, device number 12
[25007.496915] phy4 -> rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x0438 with error -19.
[25007.511944] wlan0: deauthenticating from a0:f3:c1:81:eb:f4 by local choice (reason=3)
[25007.519954] cfg80211: Calling CRDA to update world regulatory domain
[25007.563781] cfg80211: World regulatory domain updated:
[25007.563785] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[25007.563788] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[25007.563790] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[25007.563792] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[25007.563794] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[25007.563796] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
neza@neza-SATELLITE-C855-1T2:~$
sem ga dala v stand by, pol pa še restartala in se je lepo povezal..upam da je to to, če ne pa pridem povedat
hvala fantje (ali punce)!
LP, Nežolina
na routerju nimam možnosti izbire kanala.
ne vem... zakaj se pa usb wifi adapter vsakič poveže in normalno dela?
pravtako nimam nobene brezžične naprave (tipkovnice, miške), je pa res, da je zelo veliko povezav v zraku, saj živimo v bloku...
Začasna rešitev je da ponovno naložiš gonilnik za mrežno z
Več http://askubuntu.com/questions/289414/rtl8723ae-dirver-problem-ubuntu-13-04
Drug problem je da bo povezava zelo počasna, trenutno je edina rešitev da uporabiš drugo kartico. Dokler realtek ali pa skupnost ne odpravi napak.
btw gonilnik najdeš na realtekovi strani
hvala, zdaj sem vsaj prepričana, da se trenutno ne da nič narest in bom pač uporabljala usb kartico..dokler nekdo ne popravi gonilnika
drugače pa sem se z gonilnikom že ukvarjala na 12.04, ko kartica ni nobene povezave niti zaznala.na realtekovi strani pa sploh ni gonilnika za ta model kartice! pregledala sem tudi ogromno forumov, a prave rešitve ni bilo. upala sem, da bo v 13ki to rešeno, a je očitno le delno
..zato sem se opogumila in napisala post sem; v slovenščini, kar je najlažje :cool:
se tipkamo še kaj!
LP, Nežolina
Prenesti moraš http://kernel.ubuntu.com/~kernel-ppa/mainline/daily/2013-05-07-raring/linux-image-3.9.0-999-generic_3.9.0-999.201305070408_amd64.deb
http://kernel.ubuntu.com/~kernel-ppa/mainline/daily/2013-05-07-raring/linux-headers-3.9.0-999_3.9.0-999.201305070408_all.deb
http://kernel.ubuntu.com/~kernel-ppa/mainline/daily/2013-05-07-raring/linux-headers-3.9.0-999-generic_3.9.0-999.201305070408_amd64.deb
Vse skupaj namestiš z
dpkg: error processing *.deb (--install):
cannot access archive: No such file or directory
Errors were encountered while processing:
*.deb
no, jutri...
sedaj pa..
lahko noč
npr če greš v nautilusu v direktorij kjer so te datoteke in odpreš ukazno vrstico/terminal z desnim klikom.
moja težava z wifi še vedno ni rešena.za dostop do interneta uorablja usb wifi kartico, ki mi ne dela težav, vendar mi ta vgrajena "teži".okna za geslo se pojavljajo, včasih se sama poveže in mi internet zašteka..uglavnem znorela bom! :mad:
kako bi lahko onemogočila oz. preprečila tej notranji kartici delovanje?
prosim za dobesedna navodila kaj vpisat v terminal, saj sem blond :rolleyes:
hvala!
z veseljem sporočam, da mi zdaj (v novi verziji ubuntuja [13.10]) dela notranja mrežna kartica!
končno mi ni treba več pazit na štrleč usb... :rolleyes:
LP, Nežolina